Did you know what the prevailing reason for house fires is? Clogged or damaged vents are a significant cause of fire hazards according to the National Fire Protection Association. Hence, for you and your family’s safety, you should know the signs for dryer vent replacement. Although you should regularly clean your vents, you will need a professional’s help if there is damage.
What Are the Signs of Dryer Vent Replacement?
You should immediately call Dryer Vent Cleaning Cumming, if you feel your vents are blocked, or there is some issue with your dryer . You should follow these steps to be sure if your vents are obstructed or not.
Clue 1: Your Clothes Take A lot of Time to Dry
Did you observe that you need to run the dryer cycle twice to dry your clothes completely? It might be because you have either overloaded the cycle or your vents are clogged. However, if your vent is clogged, there might be limited airflow.
Clue 2: Clothes or the Dryer Becomes Very Hot After the Cycle
Your clothes should be warm after the dryer load. However, there are chances that your vents are clogged if the clothes are too hot to touch.
Clue 3: You Sense a Burning Smell Coming Out from the Dryer
If you notice smoke, it is usually due to fire. Hence, you should be alert if you sense a burning smell from your dryer. It helps prevent a fire hazard. You should know that the accumulated lint gets very hot if your vents are blocked, and the intense heat and combustible material can ignite. Hence, you can use a dryer brush kit to clean the trap or contact a dryer cleaning service. A good dryer service may also offer Heating and Air Conditioning Service Cumming.
Clue 4: Debris Lingers Out the Vent
You should examine your home from outside to locate any clogged ducts. If you see visible signs of lint accumulation on or around the vent, it’s the best time to call a professional for cleaning.
Clue 5: Dryer Need Service
If you cannot recall the last time when you had your vents cleaned by a professional, you should schedule service immediately. On the contrary, it might be the right time to hire someone.
How to Fix Damaged or Blocked Vents by Yourself?
Step 1: Put Together Your Supplies
Before you begin to fix your vents, you will require some main supplies to accomplish the steps. You would need a:
- Screwdriver
- Washrag
- Adhesive tape
- Plumbing Snake
- Garbage can
Step 2: Empty and Wash-down Lint Clog
After you collect your supplies, you can begin repairing the dryer. Start by drawing the lint trap filter from the top of the dryer or just behind the opening. Spare some time to wash the trap. You can run it under normal temperature water and pat dry with a cloth.
Step 3: Drag Dryer Away from the Wall
The following step to prevent serious vent troubleshooting is to drag your dryer away from the wall. The reason is that vent ducts are usually wrinkled foil pipes that run from the backside of the dryer to the external wall with the dryer outtake. If you pull them away, it unfolds vents and creates more space for work.
Step 5: Inspect Duct for Damages
You should closely inspect the exposed duct cylinder for any damages hindering dryer performance. Therefore, you may test for any air seepages. However, if the damage is negligible, you may not have to change the entire vent duct. You can use adhesive tape to fix it.
Step 5: Tighten Closures at Ends of the Ductwork
You will have to fully protect the closures at the ends of the vents. If the duct is unbroken, hot air can still escape and may be bad for your dryers, clothing, and energy bills. Indeed, the solution is to sensibly re-seal the ducts and then stiffen them so that it does not lose again. A tight duct seal is ideal for dryer performance.
Step 6: Replace Damaged Duct
Air leakage may not be fully repaired if you see that fixing and tightening your vents was ineffective. Then it would be ideal if you replaced the damaged ducts. For this, you will need to sensibly investigate the type and size of ducts required for your dryer model. After you are sure about the details, you can purchase a new dryer vent.
You need to get rid of the old vent duct and then carefully fix the new one. Ensure to cap the vent ducts clasps tightly at both ends so that your ducts remain in place. It will generate a fitted warm air seal to let the air out of the dryer.
Step 7: Clean the Duct Canal
You should immediately call a professional, if your ducts are clogged with lint and starts to overflow. You should shake it out and clear the duct canal before you reattach the seals. However, if the problem is severe, you may use a plumbing snake to access the ducts that run within your home, either through an external wall or into the loft.
Step 8: Check the Dryer Functioning
Lastly, when you are ready to check your dryer to see if the repair and maintenance tasks have been done rightly. Place everything back in its original place. Push the dryer back against the wall. Be careful not to crush the supple area of your dryer ducts. After this, turn on your dryer to see if it is functioning correctly and providing you fluff dry clothes.
Take Away
If you are not comfortable repairing your dryer, you should look for a reliable dryer cleaning service nearby. It would help if you never ignored clogged duct signs as they may lead to an irreplaceable loss. Ask for referrals or search online; experts always recommend a professional service.
